Forums, External Fixtures and Fittings
Questions about external fixtures and fittings (pulpit, deckgear, handrails, etc)
Latest reply
15 October 2023
22:43
Backing plates for self steering gear 2 Replies Posted 15 October 2023
Lee at 23/03/2011 09:28:04
Hello,
I am about to fit a stainless bracket to the deck (it fits around the backstay) and was wondering if anything more than penny washers are needed behind the bolts? in total the bracket, which anchors a Navik wind gear, has 16 bolts arranged over its four feet.
Also, any recommendations on a bedding compound?
Any suggestions welcome.
Lee
Latest reply
15 October 2023
22:42
Freeboard 4 Replies Posted 15 October 2023
Lee at 31/01/2011 22:30:48
Hello,
I have just bought a second hand Navik windvane and am wondering about the best way to fit it. Does anyone know the height above waterline of the teak capping on the transom?
Thanks
Lee
Latest reply
15 October 2023
22:42
Osmosis 4 Replies Posted 15 October 2023
gregcope at 17/01/2011 20:46:47
HI All,
Anyone any advice on Osmosis and possible treatment options?
Has anyone else experienced this and what did they do?
Latest reply
15 October 2023
22:42
Gebo Flushline Hatch 510X510mm ? 3 Replies Posted 15 October 2023
nardus at 07/01/2011 07:55:46
Our boat needs a new fore-hatch, so I found a cheap new Gebo Flushline Hatch 510X510mm It`s a nice smooth hatch without sharp edges to snag clothing or lines.
Does anybody know this hatch fit? or do i need another? As I red somewhere the measures for the fore-hatch would be 500×500mm…
Edited: nardus on 2016-04-04 08:54:08
Latest reply
15 October 2023
21:51
Bought a Contessa - with legs? 3 Replies Posted 15 October 2023
chris at 30/10/2010 16:50:25
Hello All,
I have read every post on this forum and it has helped me greatly. I bought the Contessa in Lisbon and sailed it down to Portimao where I am fitting it out to cross the Atlantic within the next month.
On the sail down to Lisbon we pushed her hard wanting to know everything about her, I learnt:
1. She is a wet, the floor boards are now soft / rotted as a result of both a ruptured water tanks, the gas locker filling with water, all the windows leaking. I even found a pond on the shelf in the forepeak …. goodness knows how water got there.
2. She is an absolute legend to sail!! Never had so much faith or fun sailing a yacht before. 4 meter swell 20knts of wind, the furling genoa broke we were WAY over sheeted and she took it all! She even hove to with full sails out when the life raft was sliding off the deck. Although I notice she easily digs her bow into the troughs.
The list of problems I discovered with her were swept from my memory when I saw her sailing in real winds, sadly I am now on the hard and trying to fix all the issues identified on the sea trial.
I would greatly appreciate some help identifying the following:

There are 4 of these very solid backing plates, 2 on the port side of the hull, 2 on the starboard. By the Galley / Nav station and by the Head / Locker area. Outside there are what look like blanking bolts, in the port aft locker I found 20" long 1.5" diameter stainless bolts which I assume can be screwed into these plates from outside the hull. What are these? Did this boat once have legs?
I notice the picture at the top of the forums has a C32 sinking in the mud.
Appreciate any help you can throw my way.
Kind Regards,
Chris
Latest reply
15 October 2023
21:50
Replacing windows and hatches 5 Replies Posted 15 October 2023
GlennG at 18/09/2010 19:28:05
Perle’s getting to the point where the windows are corroding and leaking and the old Gebo squeeze handle hatches are crazed and, in the case of the fore-hatch, cracked (Gaffa tape works wonders at keeping the water out!). I know that it’s difficult if not impossible to reliably replace the perspex in the Gebo hatches as you can’t get the rubber seals.
I have no time to lavish on the task, so will need to get someone else to do it. So, some questions:
- How much time would this job take? I appreciate “it depends”.
- What sort of price should I expect to pay for the whole job?
- How much for a new set of windows?
- What’s the best hatch replacement? I’ve seen some of the modern hatches are cheap and nasty; I really like solid things!
- Has anyone ever successfully replaced the perspex in a Gebo hatch?
- Who do you recommend? Perle’s in Chatham so at least three days from Lymington.
Thanks,
Glenn
Winches 0 Replies Posted 15 October 2023
Jaywalker at 07/09/2010 20:06:36
Our winches are Maxwell and spares are apparently only available from Australia at an enormous minimum cost for transport/postage. The primaries are self tailing but in practice, winching is easier ignoring the ST, using ST with 2 safety turns only to secure the sheet.
One good thing about them, once you’ve got used to it, is that the winches are asymmetric – both load from outboard.
Is there a big difference on a Co32 with the sheet leading from inboard – fouling say the spray hood or coaming? Does any other make have reversible/anticlockwise-loading winches?
Are there any hidden catches in fitting new winches, and is any make better/worse to fit?
What size primaries do most people fit?
Janet (Jaywalker)
Latest reply
15 October 2023
21:50
Sprayhoods 1 Reply Posted 15 October 2023
Conor Owens at 12/08/2010 23:42:40
Hi All,
I’m getting close to the point where I’ll need to replace the sprayhood. The windows, edgings and fastening tapes have all been replaced a few times, and it has a good few patches and repairs but at some point I’ll need to get a new one.
I’ve put some pictures of the current hood here: http://picasaweb.google.com/owens.conor/Contessa32Sprayhood?feat=directlink
Do people have any recommendations for geting a new one? I think that it should be possible to make one that comes a bit further aft at the top – there is a good 50 or 60 cms to the mainsheet when at rest, but the problem areas would be when sailing on a reach / run the mainsheet would wear on the edge of the hood. Similarly the port genoa sheet rubs – hence the leather patch on my hood.
I’m sure I saw one boat somewhere with a much deeper sprayhood but she may have had the primary winches slightly further aft than normal. Amelie of Dart maybe
I’d be grateful for any tips on what to include/avoid and if possible some pictures of alternatively shaped sprayhoods. If anyone has an extension for a full cockpit enclosure … some pictures of how those are set up would be welcome too.
Thanks,
Conor.
Latest reply
15 October 2023
21:50
Deck hand-holds 2 Replies Posted 15 October 2023
George Isted at 06/10/2009 16:58:12
In the hope that I can stop some elusive leaks I’m looking to replace the deck/coach-roof teak handrails at the same time as the toerails. Does anyone know if these are just screwed in place or are they through-bolted?
Latest reply
15 October 2023
21:50
Stanchion Posts 2 Replies Posted 15 October 2023
Waffler 333 at 13/07/2009 21:01:28
We have just returned from Brittany and have had a wonderful cruise. However, one of our original alloy stanchion holders disintegrated. It was one which was probably under most strain, having the Furlex line attached leading into the cockpit but others are showing signs of doing the same. Our boat is one of the earliest ones – Fiona Rogers tells me she was built in ’71 although registered in ’72. Fiona sent out a replacement by courier to us in Brest but we found problems with it. The early boats were bolted together and the bolt heads were hidden under the stanchion holders which had a hole through the upright part of the holder to allow the holder to sit flush. The new holder is Stainless, and without a hole and what is more, the holes for the bolts to attach it are not in the same places. We managed with help from various people to drill a hole and sort out new holes for the attachment but we will need to replace all the other holders over the winter.
So firstly, has anyone else had this problem and is there a solution? Secondly, I would advise anyone with similar alloy stanchion holders to check them for wear and tear!